Is OSHA 30 Better Than OSHA 10 – This is the question we will be answering in this article. So follow me as we go on it.
OSHA 10
The OSHA 10 construction safety course is designed to teach recognition, prevention, and avoidance on the job site. It lasts for ten hours.
A worker receives their OSHA 10 card, allowing them to work on job sites where OSHA 10 is a prerequisite, after completing the 10-hour course curriculum with a passing grade of 70% (maximum three attempts).
OSHA30
The OSHA 30 construction safety course on the other hand, is designed to teach recognition, prevention, and avoidance on the job site. It lasts for 30 hours.
A worker receives their OSHA 30 card, allowing them to work on job sites where OSHA 30 is a prerequisite, after completing the 30-hour course curriculum with a passing grade of 70% (maximum three attempts).
Comparing OSHA 10 and 30 – OSHA 10 and OSHA 30 are wellbeing accreditation programs presented by the Word related Security and Wellbeing Organization (OSHA). They train workers in the construction, maritime, and general industry to recognize and mitigate workplace hazards and understand their rights under the OSHA Act.
What are the components of OSHA 10 training?
An introduction to OSHA, including information on worker rights, employer responsibilities, and how to file a complaint, is included in OSHA 10 training, which must be delivered by a trainer authorized by OSHA. Additionally, the course provides an overview of common workplace hazards and workplace injury prevention strategies. Construction, maritime, and general industry each have their own set of mandatory subjects. The course designer can choose from a list of elective topics and procedures that are most beneficial to participants and their careers after these mandatory topics have been covered.
What are the components of OSHA 30 training?
OSHA 30 is “Awareness Training” that covers every aspect of construction site work. The OSHA 30-Hour training course provides instructors with an additional 20 hours, allowing them to discuss more safety topics and devote more time to each one. Customers have more faith in a business’s safety procedures and capacity to complete a project without causing any injuries as a result of this additional emphasis on job site risk and hazard prevention.
OSHA 30 covers advanced topics that vary by industry type in addition to the OSHA 10 requirements.
The OSHA 30 Hour Course is a comprehensive and advanced safety training program that teaches employees about the dangers and injuries that can occur at workplaces and the best ways to prevent them. Safety directors, foremen, and field supervisors are the ideal candidates for the OSHA 30 Hour Training course. As an introduction to issues pertaining to workers’ compliance with occupational safety and health regulations, the program provides comprehensive information on OSHA trainings. Participants will also receive an OSHA 30 Hour Construction Outreach course completion card upon successful completion of this course.
The 30-hour training is more expensive.
Is OSHA 30 Better Than OSHA 10
It is also important to note the following about the two when deciding which one is better.
The 10-hour OSHA training:
- Outlines the inspection’s priorities and procedure.
- Explains the role of OSHA and worker rights.
- A fundamental overview of PPE and on-the-job safety requirements like fire protection, lead and asbestos exposure, health risks, cranes, ladders, and stairways, and so on.
- Recognize the various tasks and equipment’s general safety and health provisions.
The 30-hour OSHA training:
is intended for safety directors, foremen, and supervisors and is much more extensive. In addition to covering the same material as the 10-hour course, this course assists trainees in:
- Be familiar with OSHA regulations, safety and health risks, and standards.
- Significantly increases the amount of time trainers can discuss particular subjects.
- Describe the various PPE types and their usage requirements.
- Recognize fire safety.
- Identify a variety of hazards.
- Take steps to reduce the likelihood of accidents.
- Identify safety concerns while working.
- Be aware of the safety precautions that are required in a variety of settings, including ladders, construction sites, excavation sites, confined spaces, electrical hazards, hazardous materials, and other locations.
Topics covered in between the 10-hour General Industry training and the 30-hour OSHA training
10-HOUR
- Materials That Pose a Risk
- Handling of Materials
- Guarding the Machinery
- Fundamentals of Industrial Hygiene
- Pathogens that Infect Blood
- Ergonomics
- Health and Safety Programs
- Fall Protection
30-HOUR
- Materials That Pose a Risk
- Handling of Materials
- Guarding the Machinery
- Fundamentals of Industrial Hygiene
- Pathogens that Infect Blood
- Ergonomics
- Security and Wellbeing Projects
- Protection from Falls
- Space Contained
- Lockout/Tagout
- Selective welding
Courses can be tailored to meet the needs of a construction company or construction worker by instructors. In general, fall protection, electrical safety are all covered in OSHA training.
An honest and sincere effort is made by employers who offer OSHA training to educate employees on proper safety practices can establish your safety efforts’ credibility with workers, OSHA, and the workplace culture as a whole.
Read Also: How long does it take for DOL OSHA 10/30-Hour card to expire
OSHA monitors all OSHA OutReach Trainers and Facilitators to ensure that their efforts are kept up to date with the latest regulations. In addition, they keep track of all workplace OSHA reports.
The course provides employees with all the necessary skills to work safely and maintain compliance, so employers must:
- Take into account the expenses associated with noncompliance, worker’s compensation, and the loss of skilled labor due to injury.
- If the training is done off-site, think about the cost of the instructor, the training facility, and the loss of productivity on the floor or at the worksite.
- Recognize that one week’s savings of a few thousand dollars could save millions in the future.
Other things to consider:
- Certification is valid for the employee’s entire career.
A person with a 10-hour certification can sometimes “upgrade” to a 30-hour certification within six months by completing an additional 20 hours of training.
- The Department of Labor mails a physical wallet card within approximately two weeks of successful completion.
- Most of the time, the 10-hour training is taken to meet employment and regulatory requirements. In some states and locations, additional training may be required.
- The 10- and 30-hour courses can be taken in as little as two days, respectively; however, it can’t be more than six months before a course is finished. You must start over if you take longer than six months.
- Employees can be trained for up to 7.5 hours per day. Teachers cannot instruct for more than 7.5 hours per day as facilitators.
Is OSHA 30 Better Than OSHA 10
Additionally, when deciding which one better suits your needs, take into cognizance what each of them offer as listed below. The strike through means such provision is not available on the OSHA:
OSHA10 | OSHA30 |
1. Recognize what worker rights are protected under OSHA
2. Recognize what responsibilities an employer has under OSHA 3. Identify major fall hazards 4. Identify common caught-in or -between hazards 5. Identify common struck-by hazards 6. Identify types of electrocution hazards 7. Identify ways to select appropriate PPE and lifesaving equipment 8. Identify major health hazards common to the construction industry 9. Recognize how to protect oneself from material handling hazards 10. Identify major hand & power tool hazards 11. Recognize role of the workforce in improving the current culture 12. Recognize the role of management in improving the current culture 13. Recognize ways to protect oneself from crane hazards 14. Identify major hazards related to motor vehicles, mechanized equipment and marine operations 15. Recognize ways to protect oneself from fire hazards through prevention and emergency response 16. Recognize employer requirements for protecting workers from concrete & masonry hazards, including abatement methods 17. Identify major steel erection hazards 18. Recognize ways to protect oneself from welding & cutting hazards 19. Describe types of confined space hazards 20. Recognize ways to protect oneself from confined space hazards 21. Describe activities that can lead to MSD and RMD injury and illness 22. Recognize employer requirements for providing a safety and health program that effectively reduces and prevents employee injury, illness, and fatality 23. Identify responsibilities of a supervisor in preventing worker injuries and unhealthful exposures 24. Recognize the specific legal responsibilities of a supervisor to protect worker safety and health 25. Identify the reasons for an incident investigation and future preventative measures that may result 26. Recognize ways to protect oneself from arc flash hazards 27. Describe types of health and safety construction hazards and appropriate forms mitigation |
1. Recognize what worker rights are protected under OSHA
2. Recognize what responsibilities an employer has under OSHA 3. Identify major fall hazards 4. Identify common caught-in or -between hazards 5. Identify common struck-by hazards 6. Identify types of electrocution hazards 7. Identify ways to select appropriate PPE and lifesaving equipment 8. Identify major health hazards common to the construction industry 9. Recognize how to protect oneself from material handling hazards 10. Identify major hand & power tool hazards 11. Recognize role of the workforce in improving the current culture 12. Recognize the role of management in improving the current culture 13. Recognize ways to protect oneself from crane hazards 14. Identify major hazards related to motor vehicles, mechanized equipment and marine operations 15. Recognize ways to protect oneself from fire hazards through prevention and emergency response 16. Recognize employer requirements for protecting workers from concrete & masonry hazards, including abatement methods 17. Identify major steel erection hazards 18. Recognize ways to protect oneself from welding & cutting hazards 19. Describe types of confined space hazards 20. Recognize ways to protect oneself from confined space hazards 21. Describe activities that can lead to MSD and RMD injury and illness 22. Recognize employer requirements for providing a safety and health program that effectively reduces and prevents employee injury, illness, and fatality 23. Identify responsibilities of a supervisor in preventing worker injuries and unhealthful exposures 24. Recognize the specific legal responsibilities of a supervisor to protect worker safety and health 25. Identify the reasons for an incident investigation and future preventative measures that may result 26. Recognize ways to protect oneself from arc flash hazards 27. Describe types of health and safety construction hazards and appropriate forms mitigation |
Read Also: OSHA certification online – See authorized trainers
Do You Need OSHA 10 If You Have OSHA 30?
No – As OSHA 30 covers OSHA 10 with additional 20 Hours training for Safety directors, foremen, and field supervisors, etc.